Jump to content
Show header slider

ELECTRIC SIGN SUPPLIES
If You're Looking For Premium Electric Sign Industry Components From Trim Cap, LED's, Neon Supplies, Power Supplies, Pattern Paper.  Then Please Visit Our Online Store or Feel Free To Call Us For Inquiries or Placing an Order!!
Buy Now

SIGN INSTALLER MAP
Looking for a fellow Sign Syndicate Company Member For A Sign Install or Maintenance Call?
Click Here

For Sign Company's Who Work As Subcontractors
Before You Work For A National Sign & Service Company You Need To Look At The Reviews Of These Companies Before You Work For Them. Learn When To Expect Payment From Them and What It's Like To Work For Them, The Good, The Bad, The Ugly. Learn and Share Your Experiences Yourself For Others
Click Here

Need software

signguy

By signguy
in Employment Job Listings

 Share

Recommended Posts

signguy Drive By Register

signguy

Posted
Posted (edited)

I need help finding software for a 'REFLEC-TEK' flipper style message center MFG'd by "Elctrodynamics' around 1989. The software is called "SIGNUSER" (very original), it is a DOS program. We put this sign up for a Junior High School and their computer finally gave up the ghost. They cnnot find their software so the sign is basically useless. The MFG is still in business, but quit makiing signs 10 years ago and is not able (or just unwilling) to help locate software at this point. We will pay for a copy if anyone can locate, or knows of any other sign owners by Electrodynamics we could contact.

Edited by signguydave
Link to comment
Share on other sites
  • 6 months later...
signestimators.com Drive By Register

signestimators.com

Posted
Posted

I think is going to be hard to find the software, but there are many companies that will retrofit using as much as possible of the old sign and just adjusting the software (or worst case replace the main comm board) to be compatible, hopefuly a lot cheaper that buying a new sign, do a search for led sign retrofit or score board retrofit or display sign retrofit, I retrofitted a couple of signs some time ago but I don't do that anymore.

Steve

http://www.signestimators.com/

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Topics

  • Posts

    • Rocco
      Mounting Signs On EIFS

      By Rocco · Posted

      It depends on what's under the EIFS.   If it's plywood under the foam, then toggles are fine for a lightweight sign.  If masonry, we've come to like the titen HD (simpson strong tie brand) anchors or long wedge anchors.   The Titen HD screws are more user friendly than tapcons IMO.   They come in a variety of sizes, sometimes even at the big home centers.   Just check to see if it's densglass (fiberglass wall panels) under the foam.  Engineeners have told us that densglass isn't "structural" and that things need to be thru-bolted with uni-strut (or equal) sleepers across studs inside the wall.  A few years back, we were called out for an emergency call where someone had installed some large raceway channel letter signs to an EIFS wall that had densglass behind.  They used lag screws.  These held for a while but a heavy snow caused them to fail.   And toggles should work with Densglass but again not for any heavy loads.    In any case don't compress the foam too much.  A sleeve (mentioned above) would be needed for whatever the depth of the foam might be, though probably not needed for something light like an ACM panel.   if it's a really small sign, then appropriate exterior screws are usually OK going into plywood.  
    • Johnny
      Fs: New Neon Manifold - $825

      By Johnny · Posted

      Interested in neon manifold for my personal shop 484 862 6095 ask for Johnny
    • Erik Sine
      Mounting Signs On EIFS

      By Erik Sine · Posted

      Toggle bolts
    • PhoenixStucco
      Mounting Signs On EIFS

      By PhoenixStucco · Posted

      Are there any recommendations for the best types of anchors to use for lightweight signs on EIFS?  <a href=" https://www.phoenixstuccocontractor.com/"> Phoenix Stucco Contractors</a>
    • Rocco
      Pepsi logo vinyl colors

      By Rocco · Posted

      Hi   Can anyone tell me the right color red and blue translucent vinyl for the "new" Pepsi logo?  We have a local ice cream spot that recently changed from Coke to Pepsi and we have to replace the graphics on a couple of lit cabinets.   The customer sent me the logo in various formats but it didn't specify the correct colors.   I've searched but keep getting CYMK, etc. for the older logo - 2022 or so.   Thanks!
×
×
  • Create New...