Jump to content

ELECTRIC SIGN SUPPLIES
If You're Looking For Premium Electric Sign Industry Components From Trim Cap, LED's, Neon Supplies, Power Supplies, Pattern Paper.  Then Please Visit Our Online Store or Feel Free To Call Us For Inquiries or Placing an Order!!
Buy Now

SIGN INSTALLER MAP
Looking for a fellow Sign Syndicate Company Member For A Sign Install or Maintenance Call?
Click Here

For Sign Company's Who Work As Subcontractors
Before You Work For A National Sign & Service Company You Need To Look At The Reviews Of These Companies Before You Work For Them. Learn When To Expect Payment From Them and What It's Like To Work For Them, The Good, The Bad, The Ugly. Learn and Share Your Experiences Yourself For Others

Click Here

City crews, sign shops busy fixing damage


Erik Sine

Recommended Posts

City crews, sign shops busy fixing damage

Posted: January 23, 2012 - 4:31pm

post-3-0-62194300-1327450953.jpg

By Joe Gamm

joe.gamm@amarillo.com

In all, 35,608 Xcel Energy customers in Texas and New Mexico lost power during Sunday’s windstorm, company spokesman Wes Reeves said.

Power to most customers was restored by Sunday evening, except for a few customers near Rick Husband Amarillo International Airport, Reeves said.

The windstorm also kept city crews and sign repair shops busy.

The Amarillo Fire Department responded to 78 calls Sunday, a 56 percent increase over an average day of 50 calls, Capt. Wes Hall said.

The Amarillo Police Department responded to 209 calls from 10 a.m. to 4 p.m. Sunday, a bump of 76 calls over the same time period the week before.

The department responds to a high number of security alarms set off during strong winds, Sgt. Brent Barbee said.

Amarillo Street Superintendent Chris Mitchell said the department called in personnel to help clear trees, branches and debris from city streets.

“The police department called about stuff that needed to be picked up in the street,” Mitchell said. “There were a couple of the larger tree limbs that we had to move to the side of the road, then cut up Monday.”

Replacing temporary road signs at construction sites kept street crews busiest Sunday, Mitchell said.

Hoarel Sign Co. manager Linda Cox said she was aware of a number of signs and awnings her company installed that would need to be repaired or replaced. The company has to provide estimates for insurance companies before any work is done.

“I haven’t had too many calls because the awnings are either beyond repair or completely gone,” Cox said.

You have enemies? Good. That means you've stood up for something, sometime in your life. - Winston Churchill

Link to comment
Share on other sites



  • Topics

  • Posts

    • It depends on what's under the EIFS.   If it's plywood under the foam, then toggles are fine for a lightweight sign.  If masonry, we've come to like the titen HD (simpson strong tie brand) anchors or long wedge anchors.   The Titen HD screws are more user friendly than tapcons IMO.   They come in a variety of sizes, sometimes even at the big home centers.   Just check to see if it's densglass (fiberglass wall panels) under the foam.  Engineeners have told us that densglass isn't "structural" and that things need to be thru-bolted with uni-strut (or equal) sleepers across studs inside the wall.  A few years back, we were called out for an emergency call where someone had installed some large raceway channel letter signs to an EIFS wall that had densglass behind.  They used lag screws.  These held for a while but a heavy snow caused them to fail.   And toggles should work with Densglass but again not for any heavy loads.    In any case don't compress the foam too much.  A sleeve (mentioned above) would be needed for whatever the depth of the foam might be, though probably not needed for something light like an ACM panel.   if it's a really small sign, then appropriate exterior screws are usually OK going into plywood.  
    • Interested in neon manifold for my personal shop 484 862 6095 ask for Johnny
    • Are there any recommendations for the best types of anchors to use for lightweight signs on EIFS?  <a href=" https://www.phoenixstuccocontractor.com/"> Phoenix Stucco Contractors</a>
    • Hi   Can anyone tell me the right color red and blue translucent vinyl for the "new" Pepsi logo?  We have a local ice cream spot that recently changed from Coke to Pepsi and we have to replace the graphics on a couple of lit cabinets.   The customer sent me the logo in various formats but it didn't specify the correct colors.   I've searched but keep getting CYMK, etc. for the older logo - 2022 or so.   Thanks!
×
  • Create New...