Jump to content

ELECTRIC SIGN SUPPLIES
If You're Looking For Premium Electric Sign Industry Components From Trim Cap, LED's, Neon Supplies, Power Supplies, Pattern Paper.  Then Please Visit Our Online Store or Feel Free To Call Us For Inquiries or Placing an Order!!
Buy Now

SIGN INSTALLER MAP
Looking for a fellow Sign Syndicate Company Member For A Sign Install or Maintenance Call?
Click Here

For Sign Company's Who Work As Subcontractors
Before You Work For A National Sign & Service Company You Need To Look At The Reviews Of These Companies Before You Work For Them. Learn When To Expect Payment From Them and What It's Like To Work For Them, The Good, The Bad, The Ugly. Learn and Share Your Experiences Yourself For Others

Click Here

U.S. DOE to Fund OLED Lighting Developed by DuPont


Erik Sine

Recommended Posts

U.S. DOE to Fund OLED Lighting Developed by DuPont

Nov 24,

DuPont announced that it has been awarded a US$2.25 million grant from the U.S. Department of Energy (DOE) for a two-year project to develop a solid-state lighting source using low-cost organic light emitting diode (OLED) solution-processing manufacturing techniques.

Through the grant DuPont is developing low-cost, energy efficient OLED lighting solutions that have the potential to transform the lighting market. DuPont said that solution-processing is a cost-effective technique for the manufacture of OLEDs due to its lower capital investment, reduced fixed costs, and efficient use of materials. The benefits are seen through manufacturing large areas at low cost while delivering completely new, highly efficient lighting concepts, said DuPont.

According to the Next Generation Lighting Industry Alliance, more than 20% of U.S. electrical energy in 2009 is used for lighting. The U.S. domestic market for lamps, ballasts, lighting fixtures, and lighting controls is $15 billion and $75 billion, globally. Solid-state lighting technologies, which include OLEDs, said DuPont, have the potential to save 348 trillion kilowatt-hours of electricity by 2030 compared with traditional light sources.

Compared to Light-Emitting Diodes (LEDs), which are small point sources manufactured on relatively small semiconductor wafers, DuPont said that OLEDs have a surface area light source which can be made on large sheets of glass or in a roll-to-roll process, allowing significant economies in manufacturing. Also, said DuPont, OLED lighting can use less energy and provide the same quality of light or better.

You have enemies? Good. That means you've stood up for something, sometime in your life. - Winston Churchill

Link to comment
Share on other sites



  • Topics

  • Posts

    • It depends on what's under the EIFS.   If it's plywood under the foam, then toggles are fine for a lightweight sign.  If masonry, we've come to like the titen HD (simpson strong tie brand) anchors or long wedge anchors.   The Titen HD screws are more user friendly than tapcons IMO.   They come in a variety of sizes, sometimes even at the big home centers.   Just check to see if it's densglass (fiberglass wall panels) under the foam.  Engineeners have told us that densglass isn't "structural" and that things need to be thru-bolted with uni-strut (or equal) sleepers across studs inside the wall.  A few years back, we were called out for an emergency call where someone had installed some large raceway channel letter signs to an EIFS wall that had densglass behind.  They used lag screws.  These held for a while but a heavy snow caused them to fail.   And toggles should work with Densglass but again not for any heavy loads.    In any case don't compress the foam too much.  A sleeve (mentioned above) would be needed for whatever the depth of the foam might be, though probably not needed for something light like an ACM panel.   if it's a really small sign, then appropriate exterior screws are usually OK going into plywood.  
    • Interested in neon manifold for my personal shop 484 862 6095 ask for Johnny
    • Are there any recommendations for the best types of anchors to use for lightweight signs on EIFS?  <a href=" https://www.phoenixstuccocontractor.com/"> Phoenix Stucco Contractors</a>
    • Hi   Can anyone tell me the right color red and blue translucent vinyl for the "new" Pepsi logo?  We have a local ice cream spot that recently changed from Coke to Pepsi and we have to replace the graphics on a couple of lit cabinets.   The customer sent me the logo in various formats but it didn't specify the correct colors.   I've searched but keep getting CYMK, etc. for the older logo - 2022 or so.   Thanks!
×
  • Create New...