Jump to content
Show header slider

ELECTRIC SIGN SUPPLIES
If You're Looking For Premium Electric Sign Industry Components From Trim Cap, LED's, Neon Supplies, Power Supplies, Pattern Paper.  Then Please Visit Our Online Store or Feel Free To Call Us For Inquiries or Placing an Order!!
Buy Now

SIGN INSTALLER MAP
Looking for a fellow Sign Syndicate Company Member For A Sign Install or Maintenance Call?
Click Here

For Sign Company's Who Work As Subcontractors
Before You Work For A National Sign & Service Company You Need To Look At The Reviews Of These Companies Before You Work For Them. Learn When To Expect Payment From Them and What It's Like To Work For Them, The Good, The Bad, The Ugly. Learn and Share Your Experiences Yourself For Others
Click Here

NO LED Channel Letters

Erik Sine

By Erik Sine
in General Message Board

 Share

Recommended Posts

Erik Sine Master Engineer

Erik Sine

Posted
Posted

I don't believe it, and where we find ourselves.

I'm trying to change minds of a PM so they will allow me to install a couple of sets of LED channel letters in a shopping center that only allows neon for illumination. This location screams out LEDs because of the installation. It's a remote tranny job where all flex loops from letter to letter rest on a metal ibeam. When I removed the old sign, the two home runs were 8'+ away from the first letter because of a huge i-beam that rests against the wall and each home run was full of that chalky dust from the insulation, the GTO was tatted up all around from trying to find ground.

I can't believe we live in an age where I'm having to beg for an LED installation of channel letters :crazy:

What's next? The Community Organizer, Magic Mouth and myself having a beer together at ISA?

You have enemies? Good. That means you've stood up for something, sometime in your life. - Winston Churchill

Link to comment
Share on other sites
Digital1 Apprentice

Digital1

Posted
Posted

The Property Manager is only reading the Rules and applying them in order to preserve uniformity in the shopping center's signs. The important thing is the look and since those rules were put obviously before LED lights were known then it might take a demonstration to prove that LED lit channel letters could look the same as Neon lit ones.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Topics

  • Posts

    • Rocco
      Mounting Signs On EIFS

      By Rocco · Posted

      It depends on what's under the EIFS.   If it's plywood under the foam, then toggles are fine for a lightweight sign.  If masonry, we've come to like the titen HD (simpson strong tie brand) anchors or long wedge anchors.   The Titen HD screws are more user friendly than tapcons IMO.   They come in a variety of sizes, sometimes even at the big home centers.   Just check to see if it's densglass (fiberglass wall panels) under the foam.  Engineeners have told us that densglass isn't "structural" and that things need to be thru-bolted with uni-strut (or equal) sleepers across studs inside the wall.  A few years back, we were called out for an emergency call where someone had installed some large raceway channel letter signs to an EIFS wall that had densglass behind.  They used lag screws.  These held for a while but a heavy snow caused them to fail.   And toggles should work with Densglass but again not for any heavy loads.    In any case don't compress the foam too much.  A sleeve (mentioned above) would be needed for whatever the depth of the foam might be, though probably not needed for something light like an ACM panel.   if it's a really small sign, then appropriate exterior screws are usually OK going into plywood.  
    • Johnny
      Fs: New Neon Manifold - $825

      By Johnny · Posted

      Interested in neon manifold for my personal shop 484 862 6095 ask for Johnny
    • Erik Sine
      Mounting Signs On EIFS

      By Erik Sine · Posted

      Toggle bolts
    • PhoenixStucco
      Mounting Signs On EIFS

      By PhoenixStucco · Posted

      Are there any recommendations for the best types of anchors to use for lightweight signs on EIFS?  <a href=" https://www.phoenixstuccocontractor.com/"> Phoenix Stucco Contractors</a>
    • Rocco
      Pepsi logo vinyl colors

      By Rocco · Posted

      Hi   Can anyone tell me the right color red and blue translucent vinyl for the "new" Pepsi logo?  We have a local ice cream spot that recently changed from Coke to Pepsi and we have to replace the graphics on a couple of lit cabinets.   The customer sent me the logo in various formats but it didn't specify the correct colors.   I've searched but keep getting CYMK, etc. for the older logo - 2022 or so.   Thanks!
×
×
  • Create New...