Jump to content
Show header slider

ELECTRIC SIGN SUPPLIES
If You're Looking For Premium Electric Sign Industry Components From Trim Cap, LED's, Neon Supplies, Power Supplies, Pattern Paper.  Then Please Visit Our Online Store or Feel Free To Call Us For Inquiries or Placing an Order!!
Buy Now

SIGN INSTALLER MAP
Looking for a fellow Sign Syndicate Company Member For A Sign Install or Maintenance Call?
Click Here

For Sign Company's Who Work As Subcontractors
Before You Work For A National Sign & Service Company You Need To Look At The Reviews Of These Companies Before You Work For Them. Learn When To Expect Payment From Them and What It's Like To Work For Them, The Good, The Bad, The Ugly. Learn and Share Your Experiences Yourself For Others
Click Here

sign cranes

pete71

By pete71
in Cranes, Buckets, & Trucks

 Share

Recommended Posts

pete71 Drive By Register

pete71

Posted
Posted

Looking for advice on Manitex sc85 verses an Elliott H90R we have run Elliott's for years but am considering a Manitex SC85, the lifting capacity is twice that of an Elliott, just wondering if they operate and hold up, we have had some problems with the Elliott's but haven't seen very many Manitex's around.

Link to comment
Share on other sites
  • !llumenati
paul321 Master Craftsmen

paul321

Posted
  • !llumenati
Posted

MANITEX IS THE BEST Far superior to anything else out there. When you get down to the nuts and bolts...and the construction , you will see there is a big difference

The workmanship. The quality, the way everything is done. Manitex is crane, scaled down for the sign industry.

If you look at the new Elliots, they are copying Manitex design and construction now. That says it all.

I have been running my Manitex 5 days a week plus...8 hrs a day. Since 2004 WITHOUT one single problem. The only issue I had was a blown fuse, simple repair

Contact Stamm Industries 1 800 226-5056 Ask for John or a salesman www STAMM-MFG.com

Link to comment
Share on other sites
 Share
Go to topic listing


  • Topics

  • Posts

    • Rocco
      Mounting Signs On EIFS

      By Rocco · Posted

      It depends on what's under the EIFS.   If it's plywood under the foam, then toggles are fine for a lightweight sign.  If masonry, we've come to like the titen HD (simpson strong tie brand) anchors or long wedge anchors.   The Titen HD screws are more user friendly than tapcons IMO.   They come in a variety of sizes, sometimes even at the big home centers.   Just check to see if it's densglass (fiberglass wall panels) under the foam.  Engineeners have told us that densglass isn't "structural" and that things need to be thru-bolted with uni-strut (or equal) sleepers across studs inside the wall.  A few years back, we were called out for an emergency call where someone had installed some large raceway channel letter signs to an EIFS wall that had densglass behind.  They used lag screws.  These held for a while but a heavy snow caused them to fail.   And toggles should work with Densglass but again not for any heavy loads.    In any case don't compress the foam too much.  A sleeve (mentioned above) would be needed for whatever the depth of the foam might be, though probably not needed for something light like an ACM panel.   if it's a really small sign, then appropriate exterior screws are usually OK going into plywood.  
    • Johnny
      Fs: New Neon Manifold - $825

      By Johnny · Posted

      Interested in neon manifold for my personal shop 484 862 6095 ask for Johnny
    • Erik Sine
      Mounting Signs On EIFS

      By Erik Sine · Posted

      Toggle bolts
    • PhoenixStucco
      Mounting Signs On EIFS

      By PhoenixStucco · Posted

      Are there any recommendations for the best types of anchors to use for lightweight signs on EIFS?  <a href=" https://www.phoenixstuccocontractor.com/"> Phoenix Stucco Contractors</a>
    • Rocco
      Pepsi logo vinyl colors

      By Rocco · Posted

      Hi   Can anyone tell me the right color red and blue translucent vinyl for the "new" Pepsi logo?  We have a local ice cream spot that recently changed from Coke to Pepsi and we have to replace the graphics on a couple of lit cabinets.   The customer sent me the logo in various formats but it didn't specify the correct colors.   I've searched but keep getting CYMK, etc. for the older logo - 2022 or so.   Thanks!
×
×
  • Create New...